Details | Last modification | View Log | SVN | RSS feed
| Rev | Author | Line No. | Line |
|---|---|---|---|
| 205 | arune | 1 | /********************************************* |
| 2 | * vim:sw=8:ts=8:si:et |
||
| 3 | * To use the above modeline in vim you must have "set modeline" in your .vimrc |
||
| 4 | * Author: Guido Socher |
||
| 5 | * Copyright: GPL V2 |
||
| 6 | * |
||
| 7 | * Ethernet remote device and sensor |
||
| 8 | * |
||
| 9 | * Title: Microchip ENC28J60 Ethernet Interface Driver |
||
| 10 | * Chip type : ATMEGA88 with ENC28J60 |
||
| 11 | *********************************************/ |
||
| 12 | /*----------------------------------------------------------------------------- |
||
| 13 | * Includes |
||
| 14 | *---------------------------------------------------------------------------*/ |
||
| 15 | /* system files */ |
||
| 16 | #include <avr/io.h> |
||
| 17 | |||
| 18 | /* lib files */ |
||
| 19 | #include <ip_arp_udp_tcp.h> |
||
| 20 | #include <enc28j60.h> |
||
| 21 | #include <timeout.h> |
||
| 22 | #include <avr_compat.h> |
||
| 23 | #include <net.h> |
||
| 24 | |||
| 25 | // please modify the following two lines. mac and ip have to be unique |
||
| 26 | // in your local area network. You can not have the same numbers in |
||
| 27 | // two devices: |
||
| 28 | static uint8_t mymac[6] = {0x54,0x55,0x58,0x10,0x00,0x24}; |
||
| 29 | static uint8_t myip[4] = {193,11,254,22}; |
||
| 30 | static uint16_t myport =1200; // listen port for udp |
||
| 31 | // how did I get the mac addr? Translate the first 3 numbers into ascii is: TUX |
||
| 32 | |||
| 33 | #define BUFFER_SIZE 250 |
||
| 34 | static uint8_t buf[BUFFER_SIZE+1]; |
||
| 35 | |||
| 36 | int main(void){ |
||
| 37 | |||
| 38 | |||
| 39 | uint16_t plen; |
||
| 40 | uint8_t i=0; |
||
| 41 | uint8_t payloadlen=0; |
||
| 42 | |||
| 43 | // set the clock speed to 8MHz |
||
| 44 | // set the clock prescaler. First write CLKPCE to enable setting of clock the |
||
| 45 | // next four instructions. |
||
| 46 | CLKPR=(1<<CLKPCE); |
||
| 47 | CLKPR=0; // 8 MHZ |
||
| 48 | |||
| 49 | /* enable PB0, reset as output */ |
||
| 50 | DDRB|= (1<<DDB0); |
||
| 51 | |||
| 52 | /* set output to gnd, reset the ethernet chip */ |
||
| 53 | PORTB &= ~(1<<PB0); |
||
| 54 | delay_ms(20); |
||
| 55 | /* set output to Vcc, reset inactive */ |
||
| 56 | PORTB|= (1<<PB0); |
||
| 57 | delay_ms(100); |
||
| 58 | |||
| 59 | // LED |
||
| 60 | /* enable PB1, LED as output */ |
||
| 61 | DDRD|= (1<<DDD6); |
||
| 62 | |||
| 63 | /* set output to Vcc, LED off */ |
||
| 64 | PORTD|= (1<<PD6); |
||
| 65 | |||
| 66 | /*initialize enc28j60*/ |
||
| 67 | enc28j60Init(mymac); |
||
| 68 | delay_ms(20); |
||
| 69 | |||
| 70 | /* Magjack leds configuration, see enc28j60 datasheet, page 11 */ |
||
| 71 | // LEDB=yellow LEDA=green |
||
| 72 | // |
||
| 73 | // 0x476 is PHLCON LEDA=links status, LEDB=receive/transmit |
||
| 74 | // enc28j60PhyWrite(PHLCON,0b0000 0100 0111 01 10); |
||
| 75 | enc28j60PhyWrite(PHLCON,0x476); |
||
| 76 | delay_ms(20); |
||
| 77 | |||
| 78 | /* set output to GND, red LED on */ |
||
| 79 | PORTD &= ~(1<<PD6); |
||
| 80 | i=1; |
||
| 81 | |||
| 82 | //init the ethernet/ip layer: |
||
| 83 | init_ip_arp_udp_tcp(mymac,myip,80); |
||
| 84 | |||
| 85 | while(1){ |
||
| 86 | // get the next new packet: |
||
| 87 | plen = enc28j60PacketReceive(BUFFER_SIZE, buf); |
||
| 88 | |||
| 89 | /*plen will ne unequal to zero if there is a valid |
||
| 90 | * packet (without crc error) */ |
||
| 91 | if(plen==0){ |
||
| 92 | continue; |
||
| 93 | } |
||
| 94 | // arp is broadcast if unknown but a host may also |
||
| 95 | // verify the mac address by sending it to |
||
| 96 | // a unicast address. |
||
| 97 | if(eth_type_is_arp_and_my_ip(buf,plen)){ |
||
| 98 | make_arp_answer_from_request(buf); |
||
| 99 | continue; |
||
| 100 | } |
||
| 101 | // check if ip packets (icmp or udp) are for us: |
||
| 102 | if(eth_type_is_ip_and_my_ip(buf,plen)==0){ |
||
| 103 | continue; |
||
| 104 | } |
||
| 105 | |||
| 106 | if (i){ |
||
| 107 | /* set output to Vcc, LED off */ |
||
| 108 | PORTD|= (1<<PD6); |
||
| 109 | i=0; |
||
| 110 | }else{ |
||
| 111 | /* set output to GND, LED on */ |
||
| 112 | PORTD &= ~(1<<PD6); |
||
| 113 | i=1; |
||
| 114 | } |
||
| 115 | |||
| 116 | |||
| 117 | if(buf[IP_PROTO_P]==IP_PROTO_ICMP_V && buf[ICMP_TYPE_P]==ICMP_TYPE_ECHOREQUEST_V){ |
||
| 118 | // a ping packet, let's send pong |
||
| 119 | make_echo_reply_from_request(buf,plen); |
||
| 120 | continue; |
||
| 121 | } |
||
| 122 | if (buf[IP_PROTO_P]==IP_PROTO_UDP_V){ |
||
| 123 | payloadlen=buf[UDP_LEN_L_P]-UDP_HEADER_LEN; |
||
| 124 | if (buf[UDP_DATA_P]=='t' && payloadlen==5){ |
||
| 125 | make_udp_reply_from_request(buf,"hello",6,myport); |
||
| 126 | } |
||
| 127 | } |
||
| 128 | } |
||
| 129 | return (0); |
||
| 130 | } |