Subversion Repositories HomeAutomation

Rev

Details | Last modification | View Log | SVN | RSS feed

Rev Author Line No. Line
554 andfri 1 
## Node specific configuration file for bios
361 andfri 2 
 
769 arune 3 
HW_NAME=CoreCard
4 
HW_VERSION=1
361 andfri 5 
 
585 arune 6 
# Uncomment to make node autostart after X time-msgs has been sent to node
7 
# Do not choose 0 as X, also 1 is a bad choice
8 
# This should not be used on nodes with application under developement
9 
#AUTOSTART=5
10 
 
769 arune 11 
# Node hardware id, this number should be unique on your network
880 arune 12 
# leave as <GENERATE_HW> at first compile, the build will then automatically set it to whatever gets generated (see config.h)
779 arune 13 
# Never set this manually if you are not sure what you are doing
769 arune 14 
NODE_HW_ID=<GENERATE_HW>
15 
 
16 
# example:
17 
#NODE_HW_ID=0x12345678
18 
 
19 
# This number should be unique on your network (for nodes with HW_ID it's not clear if this id is needed)
656 eqlazer 20 
NODE_ID=0x02UL
416 arune 21 
# F_CPU is the clock frequency of your microcontroller, check fuses below for external/internal clock source
22 
F_CPU=8000000UL
361 andfri 23 
 
373 arune 24 
#---MEGA8---
368 arune 25 
#MCU=atmega8
26 
#HIGHFUSE=0xd4
27 
#LOWFUSE=0x24
28 
#BOOT_START=0x1e00
29 
 
373 arune 30 
#---MEGA88---
554 andfri 31 
#MCU=atmega88
32 
#HIGHFUSE=0xdc
33 
#LOWFUSE=0xe2
34 
#EXTFUSE=0x04
35 
#BOOT_START=0x1e00
361 andfri 36 
 
554 andfri 37 
#---MEGA168---
769 arune 38 
MCU=atmega168
39 
HIGHFUSE=0xdc
40 
LOWFUSE=0xe2
41 
EXTFUSE=0x02
42 
BOOT_START=0x3c00
373 arune 43 
 
769 arune 44 
# CAN configuration (old nodes: PORTB, DDRB, PB2)
361 andfri 45 
CAN_CONTROLLER=MCP2515
769 arune 46 
MCP_CS_PORT=PORTC
47 
MCP_CS_DDR=DDRC
48 
MCP_CS_BIT=PC3
628 arune 49 
MCP_CAN_BITRATE_KBPS=250
368 arune 50 
MCP_CLOCK_FREQ_MHZ=20
628 arune 51 
MCP_CLOCK_PRESC=1
368 arune 52 
 
769 arune 53 
 
54 
 
55 
# Everything below is just help
56 
 
628 arune 57 
# For 				MCP_CLOCK_FREQ_MHZ=20	MCP_CLOCK_FREQ_MHZ=16
58 
# MCP_CLOCK_PRESC		external clock			external clock
59 
# 		1 					20MHz					16MHz
60 
# 		2					10MHz					8MHz
61 
# 		4					5MHz					4MHz
62 
# 		8					2.5MHz					2MHz
63 
# Make sure to change F_CPU accordingly if using external clock on AVR (LOWFUSE)
373 arune 64 
 
628 arune 65 
 
554 andfri 66 
#Some common settings of fuses
67 
#LOWFUSE for mega88 and mega168
368 arune 68 
#0xe7		#CKDIV8=1, external crystal
416 arune 69 
#0xe0		#CKDIV8=1, external clock   (used if mcu is clocked from can-controller, F_CPU should be 16MHz or 20MHz)
70 
#0xe2		#CKDIV8=1, internal RC      (internal AVR-clock, F_CPU should be 8MHz)
368 arune 71 
#LOWFUSE for mega8
72 
#0x24		#BODLEVEL = 4.0V, BODEN=enabled, internal 8MHz
373 arune 73 
#0x20		#BODLEVEL = 4.0V, BODEN=enabled, external clock